#Fallout 4 idle animation update#
#Fallout 4 idle animation mods#

Because then it's realy easy to overlook some conditions. And this comes especially handy when there are more complicated, nested idle conditions. The engine compares all conditions sequentially from the top of the idle animation definition, and what you see there is simply the results of all the conditions. But you have to compare with the idle animation definition in the CS. The reason why I recommended to check this console output was, that you actually can see what is happening. Tested this several times - most definitely not in my imagination or a fluke occurrence. and I just noticed that even when it works, some Player controls like cast and draw-weapon are disabled for a few seconds. It looked like a bunch of condition checks like IsWeaponOut, etc., all with ' > 0.00' after it. I did look at what the console printed when manually entering PickIdle or PlayGroup Idle 1, but not sure I understand it. Ahh the joys of modding - 10% creativity, 90% jacking with the CS to get it to do what you want it to. Rest of the time the Player gets stuck like before. Sammykins Posts: 3330 Joined: Fri 10:48 amДang! It doesn't always work. So I might need a check to make sure the active view is 3rd person before executing this script. Now the problem is the 1st person view gets all jacked up if done while in 1st person view, but from what I understand, that's an issue that's unable to be solved. Maybe the scripts don't like PickIdle with a '1' after it? Because I definitely tried 'Player.PickIdle 1.' ScriptName aaPaladinPrayScriptBegin ScriptEffectStart Player.AddItemNS aaPaladinPrayToken 1 PickIdleEndBegin ScriptEffectFinish Player.RemoveItemNS aaPaladinPrayToken 10 PickIdleEnd Pickidle does some debug output, so you can see which idles have been passed over by pickidle. If your player is still in the idle, then you can do a pickidle from the console. Only removeitem and pickidle in the effectfinish.

#Fallout 4 idle animation update#

I would suggest you comment all playgroup commands, and the effect update part. I rather believe that your idle conditions are wrong And I can't believe that it shouldn't work from within a spell finish.

#Fallout 4 idle animation mods#

I also found playgroup to be very unreliable from within a script, although there are mods (Companion on your side) which are totally based on playgroup.Д«ut pickidle always works. You shouldn't try to mix pickidles and playgroup. Any more ideas?ДЄmy Masters Posts: 3277 Joined: Thu 10:26 am I also tried RunScriptLine 'Player.Playgroup Idle 1' but it didn't work either. ScriptName aaPaladinPrayScriptShort DoneFloat TimerBegin ScriptEffectStart Player.AddItemNS aaPaladinPrayToken 1 Player.PickIdle 1 Set Timer to 0 Set Done to 0EndBegin ScriptEffectUpdate Set Timer to Timer + ScriptEffectElapsedSeconds If ( Timer > 2 ) & ( Done = 0 ) Player.RemoveItemNS aaPaladinPrayToken 10 Set Done to 1ДћndifEndBegin ScriptEffectFinish Player.RemoveItemNS aaPaladinPrayToken 10 Player.Playgroup Idle 1 Player.PickIdle 1 Player.PlayGroup CastSelf 1End Still, the Player is locked in the prayer position. I moved the RemoveToken command as you said, and then further tried to move it to an Update block to try that too. I've found that Player.PlayGroup Idle 1 works in the console to return the Player to normal, but it doesn't in the spell Finish block. I suggest you dely the removeitem to the point before the 2nd pickidle.Д¬rap. Then I think it's always a problem if you add and remove the same item (dummy) during one cycle of a script. Because idle 0 will never interrupt a running animation.